This is a mirror of discontinued 'WikiDevi'. Enjoy!
Belkin F9K1102 v3
Jump to navigation
Jump to search
Belkin F9K1102 v3
Availability: now
Manuf/OEM/ODM Arcadyan WG8015 G22
FCC approval date: 06 June 2012
Country of manuf.: China
Type: wireless router
FCC ID: K7SF9K1102V3
Industry Canada ID: 3623A-F9K1102V3
PCB ID: 141801620001J
Power: 12 VDC, 1 A
Connector type: barrel
CPU1: Broadcom BCM5358UB0
FLA1: 8 MiB8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> (Macronix MX25L6406EM2I-12G)
RAM1: 64 MiB67,108,864 B <br />524,288 Kib <br />65,536 KiB <br />512 Mib <br />0.0625 GiB <br /> (EtronTech EM6AB160TSD-5G)
Expansion IFs: USB 2.0
USB ports: 1
WI1 chip1: Broadcom BCM5358UB0
WI1 802dot11 protocols: bgn
WI1 MIMO config: 2x2:2
WI1 antenna connector: none
WI2 chip1: Broadcom BCM43236B
WI2 802dot11 protocols: an
WI2 MIMO config: 2x2:2
WI2 antenna connector: U.FL
ETH chip1: Broadcom BCM5358UB0
Switch: Broadcom BCM5358UB0
LAN speed: 100M
LAN ports: 4
WAN speed: 100M
WAN ports: 1
abgn
802dot11 OUI: none specified
| CPU1 brand | WI1 chip1 brand | WI2 chip1 brand | |
|---|---|---|---|
| Belkin F9K1102 v1 | Broadcom | Broadcom | Broadcom |
| Belkin F9K1102 v2 | Realtek | Realtek | Realtek |
| Belkin F9K1102 v3 | Broadcom | Broadcom | Broadcom |
For a list of all currently documented Broadcom chipsets with specifications, see Broadcom.
N600 DB Wireless N+ Router
"P/N: 141801620001J R01" is silkscreened on the board in the FCC photos.
Forum threads
Serial
Pinout
_ = (GND) 3 = (RxD) 2 = (TxD) 1 = [3.3v] J3
| boot log |
|---|
Decompressing...done
Init Arena
Init Devs.
Boot partition size = 131072(0x20000)
Found a 8MB ST compatible serial flash
et0: Broadcom BCM47XX 10/100/1000 Mbps
Ethernet Controller 5.70.55.34 @VERSION_TYPE@
CPU type 0x19749: 530MHz
Tot mem: 65536 KBytes
CFE mem: 0x80700000 - 0x807A1590 (660880)
Data: 0x807370C0 - 0x8073A300 (12864)
BSS: 0x8073A300 - 0x8073B590 (4752)
Heap: 0x8073B590 - 0x8079F590 (409600)
Stack: 0x8079F590 - 0x807A1590 (8192)
Text: 0x80700000 - 0x807370BC (225468)
Copying boot params.....
DONE
Bootloader version v0.12 boot_version v0.12
Project name : WG8016G22-AK
Press space bar to cancel startup...
Device eth0: hwaddr EC-1A-59-46-27-B2,
ipaddr 192.168.2.1, mask 255.255.255.0
gateway not set, nameserver not set
.... 4454076 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
Linux version 2.6.22-gcebacd5b-dirty (rick@SWI-91)
(gcc version 4.1.2) #25 Mon Mar 17 17:42:49 CST 2014
CPU revision is: 00019749
Found a 8MB ST compatible serial flash
wombo_reset set to gpio 22
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Built 1 zonelists. Total pages: 16256
Kernel command line: root=/dev/mtdblock2 console=ttyS0,115200 init=/sbin/preinit
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 256 (order: 8, 1024 bytes)
CPU: BCM5357 rev 2 at 530 MHz
Using 265.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 60104k/65536k available (2988k kernel code,
5376k reserved, 1183k data, 176k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: no core
PCI: Fixing up bus 0
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
gpio_init 156
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
fuse init (API version 7.8)
io scheduler noop registered (default)
HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
loop: module loaded
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.17
pflash: found no supported devices
sflash: squash filesystem with lzma found at block 1806
Creating 4 MTD partitions on "sflash":
0x00000000-0x00030000 : "boot"
0x00030000-0x007f0000 : "linux"
0x001c3a24-0x007f0000 : "rootfs"
0x007f0000-0x00800000 : "nvram"
usbmon: debugfs is not available
GACT probability on
Mirror/redirect action on
u32 classifier
input device check on
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (512 buckets, 4096 max)
ctnetlink v0.93: registering with nfnetlink.
BCM fast NAT: INIT
ip_tables: (C) 2000-2006 Netfilter Core Team
ClusterIP Version 0.8 loaded successfully
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 176k freed
Warning: unable to open an initial console.
Failed to execute /init
Algorithmics/MIPS FPU Emulator v1.5
[sighandler]: No more events to be processed, quitting.
[cleanup]: Waiting for children.
[cleanup]: All children terminated.
insmod: emf.ko: no module by that name found
insmod: igs.ko: no module by that name found
insmod: bcm57xx.ko: no module by that name found
insmod: usbcore.ko: no module by that name found
wl1 is up in 0 sec
Hit enter to continue...chkWl:843 ----check eth2
vlan2: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Invalid argument
wlconf: PHYTYPE: 4
eth1: Invalid argument
eth1: Invalid argument
eth1: Operation not supported
eth1: Invalid argument
eth1: Invalid argument
???Hit enter to continue...updatePIC:2831 4--0:0
Portrd: Add iptable command:
iptables -t nat -A POSTROUTING -s 192.168.2.0/24 -o vlan1 -j MASQUERADE
iptables -t nat -A POSTROUTING -s 192.168.169.0/24 -o vlan1 -j MASQUERADE
Hit enter to continue...iptables: Bad rule
(does a matching rule exist in that chain?)
rm: cannot remove '/tmp/pic_block.list': No such file or directory
start_townkyServer(878): DLNA status=1
initial_DLNA_iniFile(849): cp /usr/local/twonky/twonkyserver-default.ini
/tmp/twonkyDB/twonkyserver.ini
initial_DLNA_iniFile(856): cd /tmp/twonkyDB;
cat twonkyserver.ini | grep -v "friendlyname" > tmpServer
initial_DLNA_iniFile(861): cd /tmp/twonkyDB; echo "friendlyname=belkin.7b2_MediaServer" >> tmpServer
initial_DLNA_iniFile(866): cd /tmp/twonkyDB;
rm -f twonkyserver.ini; cp tmpServer twonkyserver.ini;
start_townkyServer(892): start up the twonkyserver..
Daemonizing...
|
| wl revinfo |
|---|
# wl -i eth1 revinfo vendorid 0x14e4 deviceid 0x4329 radiorev 0x52057000 chipnum 0x5357 chiprev 0x2 chippackage 0x8 corerev 0x1c boardid 0x550 boardvendor 0x14e4 boardrev P200 driverrev 0x5463722 ucoderev 0x256013e bus 0x0 phytype 0x4 phyrev 0x9 anarev 0x0 # wl -i eth2 revinfo vendorid 0x14e4 deviceid 0x4346 radiorev 0x72057000 chipnum 0xa8e4 chiprev 0x3 chippackage 0x4 corerev 0x18 boardid 0x521 boardvendor 0x14e4 boardrev P113 driverrev 0x5463722 ucoderev 0x256013e bus 0x0 phytype 0x4 phyrev 0x9 anarev 0x0 |
cat /proc/mtd
# cat /proc/mtd dev: size erasesize name mtd0: 00030000 00010000 "boot" mtd1: 007c0000 00010000 "linux" mtd2: 0062c5dc 00010000 "rootfs" mtd3: 00010000 00010000 "nvram"
cat /proc/cpuinfo
# cat /proc/cpuinfo system type : Broadcom BCM5357 chip rev 2 processor : 0 cpu model : MIPS 74K V4.9 BogoMIPS : 264.60 wait instruction : no microsecond timers : yes tlb_entries : 64 extra interrupt vector : no hardware watchpoint : yes ASEs implemented : mips16 dsp VCED exceptions : not available VCEI exceptions : not available unaligned_instructions : 541 dcache hits : 2147483648 dcache misses : 201129644 icache hits : 2147483648 icache misses : 4239510487 instructions : 2147483648
lsmod
# lsmod Module Size Used by Tainted: PF usb_storage 45296 0 jcp 18928 0 sxuptp_driver 6176 0 sxuptp_usbmode 4368 0 ohci_hcd 26384 0 sxuptp 42336 3 jcp,sxuptp_driver,sxuptp_usbmode sxuptp_wq 1712 1 sxuptp wl_high 1148144 0 ehci_hcd 46496 0 wl 1780800 0 et 59328 0 ctf 15712 0
| netstat -l |
|---|
# netstat -l Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 router.Belkin:9090 0.0.0.0:* LISTEN tcp 0 0 192.168.169.1:9000 0.0.0.0:* LISTEN tcp 0 0 router.Belkin:9000 0.0.0.0:* LISTEN tcp 0 0 localhost.localdomain:9000 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:139 0.0.0.0:* LISTEN tcp 0 0 192.168.169.1:8080 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:51890 0.0.0.0:* LISTEN tcp 0 0 192.168.169.1:1780 0.0.0.0:* LISTEN tcp 0 0 router.Belkin:1780 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:53 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:445 0.0.0.0:* LISTEN netstat: no support for 'AF INET6 (tcp)' on this system udp 0 0 0.0.0.0:32769 0.0.0.0:* udp 0 0 192.168.169.1:1030 0.0.0.0:* udp 0 0 router.Belkin:1030 0.0.0.0:* udp 0 0 0.0.0.0:37000 0.0.0.0:* udp 0 0 0.0.0.0:137 0.0.0.0:* udp 0 0 0.0.0.0:137 0.0.0.0:* udp 0 0 0.0.0.0:137 0.0.0.0:* udp 0 0 0.0.0.0:137 0.0.0.0:* udp 0 0 0.0.0.0:138 0.0.0.0:* udp 0 0 0.0.0.0:138 0.0.0.0:* udp 0 0 localhost.localdomain:38032 0.0.0.0:* udp 0 0 localhost.localdomain:40100 0.0.0.0:* udp 0 0 localhost.localdomain:40101 0.0.0.0:* udp 0 0 localhost.localdomain:40500 0.0.0.0:* udp 0 0 0.0.0.0:53 0.0.0.0:* udp 0 0 localhost.localdomain:40000 0.0.0.0:* udp 0 0 localhost.localdomain:40001 0.0.0.0:* udp 0 0 0.0.0.0:67 0.0.0.0:* udp 0 0 0.0.0.0:67 0.0.0.0:* udp 0 0 0.0.0.0:67 0.0.0.0:* udp 0 0 localhost.localdomain:37064 0.0.0.0:* udp 0 0 0.0.0.0:49235 0.0.0.0:* udp 0 0 0.0.0.0:19540 0.0.0.0:* udp 0 0 0.0.0.0:19541 0.0.0.0:* udp 0 0 0.0.0.0:39000 0.0.0.0:* udp 0 0 localhost.localdomain:40040 0.0.0.0:* udp 0 0 0.0.0.0:5353 0.0.0.0:* udp 0 0 0.0.0.0:5353 0.0.0.0:* udp 0 0 224.0.0.251:5353 0.0.0.0:* udp 0 0 localhost.localdomain:40041 0.0.0.0:* udp 0 0 239.255.255.250:1900 0.0.0.0:* udp 0 0 192.168.169.1:1900 0.0.0.0:* udp 0 0 239.255.255.250:1900 0.0.0.0:* udp 0 0 router.Belkin:1900 0.0.0.0:* udp 0 0 239.255.255.250:1900 0.0.0.0:* udp 0 0 0.0.0.0:1900 0.0.0.0:* udp 0 0 0.0.0.0:38000 0.0.0.0:* udp 0 0 239.255.255.250:3702 0.0.0.0:* netstat: no support for 'AF INET6 (udp)' on this system raw 0 0 0.0.0.0:2 0.0.0.0:* 7 netstat: no support for 'AF INET6 (raw)' on this system Active UNIX domain sockets (only servers) Proto RefCnt Flags Type State I-Node Path |
| ps w |
|---|
# ps w
PID Uid VSZ Stat Command
1 0 3748 S /sbin/preinit
2 0 SW< [kthreadd]
3 0 SWN [ksoftirqd/0]
4 0 SW< [events/0]
5 0 SW< [khelper]
31 0 SW< [kblockd/0]
32 0 SW< [ksuspend_usbd]
35 0 SW< [khubd]
59 0 SW [pdflush]
60 0 SW [pdflush]
61 0 SW< [kswapd0]
62 0 SW< [aio/0]
87 0 SW< [mtdblockd]
347 0 4060 S httpd
351 0 1400 S minhttpd /tmp/land_httpd.pro
356 0 2792 S upnp -D -W vlan1
383 0 1984 S /usr/sbin/dnsmasq -n -i br0 -i br1 -r /tmp/resolv.conf
385 0 1808 S /bin/eapd
388 0 2304 S nas
392 0 3064 S /bin/wps_monitor
394 0 2408 S /usr/sbin/ledd
410 0 1432 S igmp vlan1
413 0 1872 S lld2d br0
423 0 SW< [sxuptp-wq]
426 0 SW [sxuptp-ka]
442 0 SW [jcpcore]
456 0 2752 S /usr/sbin/portrd
458 0 2720 S /usr/sbin/usb_wlc_status
460 0 3740 S /sbin/guestchk
462 0 1796 S sxhotplugd -f /tmp/sxnasplus/sxhotplugd.conf -l 4 -D
463 0 1796 S sxhotplugd -f /tmp/sxnasplus/sxhotplugd.conf -l 4 -D
471 0 1796 S sxhotplugd -f /tmp/sxnasplus/sxhotplugd.conf -l 4 -D
474 0 1588 S /sbin/sxnas-fssd -f /tmp/sxnasplus/sxnas.conf
476 0 1400 S minhttpd /tmp/guest_httpd.pro
478 0 2404 S reset_button
482 0 1944 S /sbin/sxnas-nsd -f /tmp/sxnasplus/sxnas.conf -i br0 -D
483 0 1944 S /sbin/sxnas-nsd -f /tmp/sxnasplus/sxnas.conf -i br0 -D
485 0 1944 S /sbin/sxnas-nsd -f /tmp/sxnasplus/sxnas.conf -i br0 -D
490 0 1548 S /sbin/jcpd -i br0
496 0 1944 S /sbin/sxnas-nsd -f /tmp/sxnasplus/sxnas.conf -i br0 -D
497 0 1944 S /sbin/sxnas-nsd -f /tmp/sxnasplus/sxnas.conf -i br0 -D
498 0 1944 S /sbin/sxnas-nsd -f /tmp/sxnasplus/sxnas.conf -i br0 -D
499 0 1944 S /sbin/sxnas-nsd -f /tmp/sxnasplus/sxnas.conf -i br0 -D
508 0 2184 S udhcpd /tmp/udhcpd0.conf
517 0 2184 S udhcpd /tmp/udhcpd1.conf
529 0 3656 S devidentd -d -i br0 -f /etc/devidentd.conf
542 0 2164 S udhcpc -i vlan1 -p /var/run/udhcpc0.pid -s /tmp/udhcpc
634 0 2424 S /usr/sbin/wanstatus
636 0 3732 S /sbin/acscher
641 0 2068 S /sbin/ulogd -d
793 0 1436 S /usr/local/twonky/twonkystarter -D -appdata /tmp/twonkyDB
794 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
807 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
808 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
989 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
990 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
991 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
992 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
993 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
998 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
999 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
1002 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
1003 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
1009 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
1014 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
1015 0 6840 R /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
1016 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
1017 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
1018 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
1019 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
1020 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
1021 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
1022 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
1023 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
1030 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
1031 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
1032 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
1033 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
1034 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
1035 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
1038 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
1041 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
1052 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
1102 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
1226 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
1227 0 6840 S /usr/local/twonky/twonkyserver -D -appdata /tmp/twonkyDB
1444 0 1852 S /bin/sh
1848 0 1848 R ps w
|
nvram dump