This is a mirror of discontinued 'WikiDevi'. Enjoy!

Xiaomi Mi Router 4A 100M (R4AC)

From DeviWiki (ex WikiDevi)
Jump to navigation Jump to search

Xiaomi Mi Router 4A
Availability: 2020

EAN: 6970244525536 (UPC DB, On eBay)
Country of manuf.: China
Serial Num Prefix: 25090/XXXXXXXXX

Amazon image

ASIN
B085G5CDY7 (13px, On Amazon, On CCC)
On Banggood

Type: wireless router

FCC ID: 2AFZZR4AC

Power: 12 VDC, 1 A
Connector type: barrel

CPU1: Mediatek MT7628DAN (575 MHz)
FLA1: 16 MiB16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br /> (Winbond 25Q128JVSQ)
RAM1: 64 MiB67,108,864 B <br />524,288 Kib <br />65,536 KiB <br />512 Mib <br />0.0625 GiB <br /> (MediaTek MT7628DAN)

Expansion IFs: none specified
Serial: 4-pad header (115200,8,N,1),

WI1 chip1: Mediatek MT7628DAN
WI1 802dot11 protocols: bgn
WI1 MIMO config: 1x1:?
WI1 antenna connector: soldered
WI2 chip1: Mediatek MT7612EN
WI2 802dot11 protocols: an+ac
WI2 MIMO config: 1x1:?
WI2 antenna connector: soldered

ETH chip1: Mediatek MT7628DAN
Switch: Mediatek MT7628DAN
LAN speed: 10/100
LAN ports: 2
WAN speed: 10/100
WAN ports: 1

abgn+ac

Stock bootloader: U-Boot 1.1.3

Stock FW OS: Linux 3.10.14 OpenWrt-deriv

Third party firmware supported: OpenWrt

Flags: MIMO

Default SSID: Xiaomi_XXXX (14 addl. devices), Xiaomi_XXXX_5G (10 addl. devices)
Default IP address: 192.168.31.1
the IP 192.168.31.1 is used by 15 additional devices
of which 14 are Xiaomi devices

802dot11 OUI: 88:C3:97
Ethernet OUI: 88:C3:97

For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.


SKU: DVB4230GL
PCB: MTO-WRM49-V1.2

Images


OEM Boot log (firmware version 3.0.5)
[03010D09][03010D0E][87850000][33325654][00333257]

DU Setting Cal Done



U-Boot 1.1.3 (Feb 28 2020 - 07:20:39)


Board: Ralink APSoC DRAM:  64 MB

Power on memory test. Memory size= 64 MB...OK!

relocate_code Pointer at: 83fb0000

RT2880_RSTSTAT_REG 0xc0030000

***************************

Board power on Occurred

***************************

flash manufacture id: ef, device id 40 18

find flash: W25Q128BV

env is right!

============================================ 

Ralink UBoot Version: 4.3.0.0

-------------------------------------------- 

ASIC 7628_MP (Port5<->None)

DRAM component: 512 Mbits DDR, width 16

DRAM bus: 16 bit

Total memory: 64 MBytes

Flash component: SPI Flash

Date:Feb 28 2020  Time:07:20:39

============================================ 

icache: sets:512, ways:4, linesz:32 ,total:65536

dcache: sets:256, ways:4, linesz:32 ,total:32768 


 ##### The CPU freq = 575 MHZ #### 

 estimate memory size =64 Mbytes

RESET MT7628 PHY!!!!!!

Please choose the operation: 

   1: Load system code to SDRAM via TFTP. 

   2: Load system code then write to Flash via TFTP. 

   3: Boot system code via Flash (default).

   4: Entr boot command line interface.

   9: Load Boot Loader code then write to Flash via TFTP. 


   n3: System Boot system code via Flash.

Booting System 1

Erasing SPI Flash...

raspi_erase: offs:20000 len:10000

.

Writing to SPI Flash...

.

done

## Booting image at bc260000 ...

   Image Name:   MIPS OpenWrt Linux-3.10.14

   Image Type:   MIPS Linux Kernel Image (lzma compressed)

   Data Size:    1424948 Bytes =  1.4 MB

   Load Address: 80000000

   Entry Point:  80000000

   Verifying Checksum ... OK

   Uncompressing Kernel Image ... OK

Erasing SPI Flash...

raspi_erase: offs:20000 len:10000

.

Writing to SPI Flash...

.

done

commandline uart_en=0 factory_mode=0 mem=64m root=/dev/mtdblock8

No initrd

## Transferring control to Linux (at address 80000000) ...

## Giving linux memsize in MB, 64


Starting kernel ...



LINUX started...

 THIS IS ASIC
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.10.14 (jenkins@27cfea1571da) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 MiWiFi-R4AC-3.0.5 Fri Feb 28 07:32:29 UTC 2020
[    0.000000] 
[    0.000000]  The CPU feqenuce set to 575 MHz
[    0.000000] 
[    0.000000]  MIPS CPU sleep mode enabled.
[    0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
[    0.000000] Software DMA cache coherency
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] User-defined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] Primary instruction cache 64kB, 4-way, VIPT, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyS1,115200n8 uart_en=0 factory_mode=0 mem=64m root=/dev/mtdblock8
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=0006b9d7
[    0.000000] Readback ErrCtl register=0006b9d7
[    0.000000] allocated 131072 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Memory: 60488k/65536k available (3212k kernel code, 5048k reserved, 723k data, 220k init, 0k highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:128
[    0.000000] console [ttyS1] enabled
[    0.120000] Calibrating delay loop... 380.92 BogoMIPS (lpj=1904640)
[    0.180000] pid_max: default: 32768 minimum: 301
[    0.180000] Mount-cache hash table entries: 512
[    0.190000] Initializing cgroup subsys memory
[    0.190000] Initializing cgroup subsys net_cls
[    0.200000] NET: Registered protocol family 16
[    0.200000] RALINK_GPIOMODE = 54054404 
[    0.210000] RALINK_GPIOMODE = 54044404 
[    0.310000] ***** Xtal 25MHz *****
[    0.310000] start PCIe register access
[    0.810000] RALINK_RSTCTRL = 2400000
[    0.820000] RALINK_CLKCFG1 = fdbfffc0
[    0.820000] 
[    0.820000] *************** MT7628 PCIe RC mode *************
[    1.320000] PCIE0 enabled
[    1.320000] Port 0 N_FTS = 1b105000
[    1.330000] init_rt2880pci done
[    1.350000] bio: create slab <bio-0> at 0
[    1.360000] PCI host bridge to bus 0000:00
[    1.360000] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
[    1.370000] pci_bus 0000:00: root bus resource [io  0x10160000-0x1016ffff]
[    1.370000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    1.380000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    1.380000] pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
[    1.390000] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
[    1.390000] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
[    1.400000] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
[    1.400000] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
[    1.410000] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
[    1.410000] pci 0000:00:00.0: PCI bridge to [bus 01]
[    1.420000] pci 0000:00:00.0:   bridge window [mem 0x20000000-0x200fffff]
[    1.420000] pci 0000:00:00.0:   bridge window [mem 0x20100000-0x201fffff pref]
[    1.430000] BAR0 at slot 0 = 0
[    1.430000] bus=0x0, slot = 0x0
[    1.430000] res[0]->start = 0
[    1.430000] res[0]->end = 0
[    1.440000] res[1]->start = 20200000
[    1.440000] res[1]->end = 2020ffff
[    1.440000] res[2]->start = 0
[    1.450000] res[2]->end = 0
[    1.450000] res[3]->start = 0
[    1.450000] res[3]->end = 0
[    1.450000] res[4]->start = 0
[    1.460000] res[4]->end = 0
[    1.460000] res[5]->start = 0
[    1.460000] res[5]->end = 0
[    1.460000] bus=0x1, slot = 0x0
[    1.470000] res[0]->start = 20000000
[    1.470000] res[0]->end = 200fffff
[    1.470000] res[1]->start = 0
[    1.480000] res[1]->end = 0
[    1.480000] res[2]->start = 0
[    1.480000] res[2]->end = 0
[    1.480000] res[3]->start = 0
[    1.490000] res[3]->end = 0
[    1.490000] res[4]->start = 0
[    1.490000] res[4]->end = 0
[    1.490000] res[5]->start = 0
[    1.500000] res[5]->end = 0
[    1.500000] cfg80211: Calling CRDA to update world regulatory domain
[    1.510000] Switching to clocksource Ralink Systick timer
[    1.510000] NET: Registered protocol family 2
[    1.520000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    1.520000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    1.530000] TCP: Hash tables configured (established 512 bind 512)
[    1.530000] TCP: reno registered
[    1.540000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    1.540000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    1.550000] NET: Registered protocol family 1
[    1.570000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.580000] jffs2: version 2.2. (ZLIB) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    1.580000] msgmni has been set to 118
[    1.590000] io scheduler noop registered
[    1.590000] io scheduler deadline registered (default)
[    1.600000] MIWIFI panic notifier registered
[    1.600000] pcieport 0000:00:00.0: device [14c3:0801] has invalid IRQ; check vendor BIOS
[    1.620000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    1.620000] serial8250: ttyS0 at MMIO 0x10000d00 (irq = 21) is a 16550A
[    1.630000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
[    1.640000] led=44, on=4000, off=1, blinks,=1, reset=1, time=4000
[    1.640000] Ralink gpio driver initialized
[    1.650000] flash manufacture id: ef, device id 40 18
[    1.650000] W25Q128BV(ef 40180000) (16384 Kbytes)
[    1.660000] mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
[    1.670000] Creating 8 MTD partitions on "raspi":
[    1.670000] 0x000000000000-0x000001000000 : "ALL"
[    1.680000] 0x000000000000-0x000000020000 : "Bootloader"
[    1.690000] 0x000000020000-0x000000030000 : "Config"
[    1.690000] 0x000000030000-0x000000040000 : "Factory"
[    1.700000] 0x000000040000-0x000000050000 : "crash"
[    1.710000] 0x000000050000-0x000000060000 : "cfg_bak"
[    1.710000] 0x000000060000-0x000000260000 : "overlay"
[    1.720000] 0x000000260000-0x000001000000 : "OS1"
[    1.730000] mtd: try split OS1 partition
[    1.730000] mtd: split_firmware
[    1.730000] mtd: firmware_partition->size   0xda0000
[    1.740000] mtd: firmware_partition->offset 0x260000
[    1.740000] mtd: uimage_len 1425012
[    1.750000] mtd: uimage_len 1441792
[    1.750000] mtd: rootfs_partition->size   0xc40000
[    1.760000] mtd: rootfs_partition->offset 0x3c0000
[    1.760000] mtd: partition "rootfs" created automatically, ofs=3C0000, len=C40000 
[    1.770000] 0x0000003c0000-0x000001000000 : "rootfs"
[    1.780000] PPP generic driver version 2.4.2
[    1.780000] PPP MPPE Compression module registered
[    1.790000] NET: Registered protocol family 24
[    1.790000] PPTP driver version 0.8.5
[    1.800000] GMAC1_MAC_ADRH -- : 0x000088c3
[    1.800000] GMAC1_MAC_ADRL -- : 0x97XXXXXX
[    1.800000] Ralink APSoC Ethernet Driver Initilization. v3.1  256 rx/tx descriptors allocated, mtu = 1500!
[    1.810000] GMAC1_MAC_ADRH -- : 0x000088c3
[    1.820000] GMAC1_MAC_ADRL -- : 0x97XXXXXX
[    1.820000] PROC INIT OK!
[    1.830000] Ralink APSoC Hardware Watchdog Timer
[    1.830000] Mirror/redirect action on
[    1.830000] u32 classifier
[    1.840000]     input device check on
[    1.840000]     Actions configured
[    1.840000] Netfilter messages via NETLINK v0.30.
[    1.850000] nfnl_acct: registering with nfnetlink.
[    1.850000] nf_conntrack version 0.5.0 (945 buckets, 3780 max)
[    1.860000] ipip: IPv4 over IPv4 tunneling driver
[    1.870000] gre: GRE over IPv4 demultiplexor driver
[    1.870000] ip_gre: GRE over IPv4 tunneling driver
[    1.880000] ip_tables: (C) 2000-2006 Netfilter Core Team
[    1.880000] Type=Restricted Cone
[    1.890000] TCP: cubic registered
[    1.890000] NET: Registered protocol family 10
[    1.900000] NET: Registered protocol family 17
[    1.900000] l2tp_core: L2TP core driver, V2.0
[    1.910000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[    1.910000] l2tp_netlink: L2TP netlink interface
[    1.920000] 8021q: 802.1Q VLAN Support v1.8
[    1.940000] VFS: Mounted root (squashfs filesystem) readonly on device 31:8.
[    1.950000] Freeing unused kernel memory: 220K (803d9000 - 80410000)
config core 'version'
	# ROM ver
	option ROM '3.0.5'
	# channel
	option CHANNEL 'release'
	# hardware platform R1AC or R1N etc.
	option HARDWARE 'R4AC'
	# CFE ver
	option UBOOT '1.0.0'
	# Linux Kernel ver
	option LINUX '0.0.1'
	# RAMFS ver
	option RAMFS '0.0.1'
	# SQUASHFS ver
	option SQAFS '0.0.1'
	# ROOTFS ver
	option ROOTFS '0.0.1'
	#build time
	option BUILDTIME 'Fri, 28 Feb 2020 07:19:54 +0000'
	#build timestamp
	option BUILDTS '1582874394'
	#build git tag
	option GTAG 'commit c6309716fe8a0c6d75bc2c4d879243fcdc588833'
[    3.720000] Raeth v3.1 (Tasklet,SkbRecycle)
[    3.720000] 
[    3.720000] phy_tx_ring = 0x03420000, tx_ring = 0xa3420000
[    3.730000] 
[    3.730000] phy_rx_ring0 = 0x03421000, rx_ring0 = 0xa3421000
[    3.750000] config 7628 esw as WLLLL
[    3.830000] GMAC1_MAC_ADRH -- : 0x000088c3
[    3.830000] GMAC1_MAC_ADRL -- : 0x97XXXXXX
[    3.840000]  Link Status Changed: Port 6 linked Up.
- preinit -
Fri Feb 28 07:32:29 UTC 2020
- regular preinit -
/lib/preinit.sh: line 1: pi_indicate_led: not found
jffs2 not ready yet; using ramdisk
-----------------------------do_data_mount_fail_recover
1+0 records in
1+0 records out
- init -
[    5.610000] ra2880stop()...Done
[    5.610000] Free TX/RX Ring Memory!

init started: BusyBox v1.19.4 (2020-02-28 07:17:56 UTC)

Please press Enter to activate this console. rcS S boot: INFO: rc script run time limit to 65 seconds.
[    5.960000] MIWIFI crash syslog initialize skiped! Code=1
[    7.680000] xt_time: kernel timezone is +0800
[    7.820000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    7.950000] nf_nat_amanda: Unknown symbol nf_nat_amanda_hook (err 0)
[    8.050000] ip_set: protocol 6
[    8.100000] ipaccount: ifname [lo] event[5]
[    8.100000] ipaccount: ifname [ifb0] event[5]
[    8.110000] ipaccount: ifname [eth0] event[5]
[    8.110000] ipaccount: ifname [tunl0] event[5]
[    8.120000] ipaccount: ifname [gre0] event[5]
[    8.120000] ipaccount: ifname [gretap0] event[5]
[    8.130000] dev_redirect OFF.dev_redirect load success. 
[    9.280000] 
[    9.280000] 
[    9.280000] === pAd = c0680000, size = 1763448 ===
[    9.280000] 
[    9.290000] <-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x
[    9.300000] <-- RTMPAllocAdapterBlock, Status=0
[    9.300000] RtmpChipOpsHook(492): Not support for HIF_MT yet!
[    9.310000] mt7628_init()-->
[    9.310000] mt7628_init(FW(8a00), HW(8a01), CHIPID(7628))
[    9.310000] e2.bin mt7628_init(1120)::(2), pChipCap->fw_len(63984)
[    9.320000] mt_bcn_buf_init(218): Not support for HIF_MT yet!
[    9.330000] <--mt7628_init()
[    9.330000] ipaccount: ifname [wl1] event[16]
[    9.340000] ipaccount: ifname [wl1] event[5]
[   10.400000] <-- RTMPAllocTxRxRingMemory, Status=0
[   10.420000] <-- RTMPAllocAdapterBlock, Status=0
[   10.430000] pAd->CSRBaseAddress =0xc0c00000, csr_addr=0xc0c00000!
[   10.430000] <dbg> MAC_CSR0=1986146304, RtmpChipOpsHook
[   10.440000] <dbg> dev idx = 1!
[   10.440000] <dbg> get_dev_config_idx pAd->MACVersion = 76623000, pAd->ChipID = 76120044
[   10.450000] ipaccount: ifname [wl0] event[16]
[   10.460000] ipaccount: ifname [wl0] event[5]
Fri Feb 28 08:32:36 CET 2020 netconfig[741]: INFO: loading exist /etc/config/network.
Fri Feb 28 08:32:36 CET 2020 netconfig[741]: config interface 'loopback'
Fri Feb 28 08:32:36 CET 2020 netconfig[741]: option ifname 'lo'
Fri Feb 28 08:32:36 CET 2020 netconfig[741]: option proto 'static'
Fri Feb 28 08:32:36 CET 2020 netconfig[741]: option ipaddr '127.0.0.1'
Fri Feb 28 08:32:36 CET 2020 netconfig[741]: option netmask '255.0.0.0'
Fri Feb 28 08:32:36 CET 2020 netconfig[741]: config interface 'lan'
Fri Feb 28 08:32:36 CET 2020 netconfig[741]: option ifname 'eth0.1'
Fri Feb 28 08:32:36 CET 2020 netconfig[741]: option type 'bridge'
Fri Feb 28 08:32:36 CET 2020 netconfig[741]: option proto 'static'
Fri Feb 28 08:32:36 CET 2020 netconfig[741]: option ipaddr '192.168.31.1'
Fri Feb 28 08:32:36 CET 2020 netconfig[741]: option netmask '255.255.255.0'
Fri Feb 28 08:32:36 CET 2020 netconfig[741]: option ip6assign '64'
Fri Feb 28 08:32:36 CET 2020 netconfig[741]: list ip6class 'ifb'
Fri Feb 28 08:32:36 CET 2020 netconfig[741]: config interface 'wan'
Fri Feb 28 08:32:36 CET 2020 netconfig[741]: option ifname 'eth0.2'
Fri Feb 28 08:32:36 CET 2020 netconfig[741]: option proto 'dhcp'
Fri Feb 28 08:32:36 CET 2020 netconfig[741]: config interface 'ifb'
Fri Feb 28 08:32:36 CET 2020 netconfig[741]: option ifname 'ifb0'
Fri Feb 28 08:32:36 CET 2020 netconfig[741]: config interface 'ready'
Fri Feb 28 08:32:36 CET 2020 netconfig[741]: option proto 'static'
Fri Feb 28 08:32:36 CET 2020 netconfig[741]: option ipaddr '169.254.29.1'
Fri Feb 28 08:32:36 CET 2020 netconfig[741]: option netmask '255.255.255.0'
Fri Feb 28 08:32:36 CET 2020 netconfig[741]: config interface 'openvpn'
Fri Feb 28 08:32:36 CET 2020 netconfig[741]: option ifname 'tun0'
Fri Feb 28 08:32:36 CET 2020 netconfig[741]: option proto 'openvpn'
[   14.420000] ipaccount: ifname [br-lan] event[16]
[   14.430000] ipaccount: ifname [br-lan] event[5]
[   14.440000] ipaccount: ifname [eth0] event[13]
[   14.440000] Raeth v3.1 (Tasklet,SkbRecycle)
[   14.450000] 
[   14.450000] phy_tx_ring = 0x0218d000, tx_ring = 0xa218d000
[   14.450000] 
[   14.450000] phy_rx_ring0 = 0x0219b000, rx_ring0 = 0xa219b000
[   14.470000] config 7628 esw as WLLLL
[   14.550000] GMAC1_MAC_ADRH -- : 0x000088c3
[   14.550000] GMAC1_MAC_ADRL -- : 0x97XXXXXX
[   14.560000] ipaccount: ifname [eth0] event[1]
[   14.590000] ipaccount: ifname [eth0.1] event[16]
[   14.590000] ipaccount: ifname [eth0.1] event[5]
[   14.610000] ipaccount: ifname [eth0.1] event[13]
[   14.610000] ipaccount: ifname [eth0.1] event[1]
[   14.630000] ipaccount: ifname [eth0.1] event[20]
[   14.630000] device eth0.1 entered promiscuous mode
[   14.640000] device eth0 entered promiscuous mode
[   14.640000] ipaccount: ifname [br-lan] event[11]
[   14.640000] ipaccount: ifname [br-lan] event[8]
[   14.680000] ipaccount: ifname [br-lan] event[8]
[   14.680000] ipaccount: ifname [br-lan] event[13]
[   14.690000] br-lan: port 1(eth0.1) entered forwarding state
[   14.690000] br-lan: port 1(eth0.1) entered forwarding state
[   14.700000] ipaccount: ifname [br-lan] event[1]
[   14.720000] ipaccount: ifname [ifb0] event[13]
[   14.730000] ipaccount: ifname [ifb0] event[1]
[   14.760000] ipaccount: ifname [lo] event[13]
[   14.760000] ipaccount: ifname [lo] event[1]
[   14.770000] ipaccount: ifname [eth0.2] event[16]
[   14.780000] ipaccount: ifname [eth0.2] event[5]
[   14.810000] ipaccount: ifname [eth0.2] event[13]
[   14.810000] ipaccount: ifname [eth0.2] event[1]
[   15.440000] ipaccount: ifname [eth0.1] event[4]
[   15.440000] ipaccount: ifname [br-lan] event[4]
[   15.440000] ipaccount: ifname [eth0.2] event[4]
[   16.690000] br-lan: port 1(eth0.1) entered forwarding state
[   17.440000] ipaccount: ifname [wl0] event[13]
[   17.450000] <dbg> MAC_CSR0=1986146304, rtmp_asic_top_init
[   17.500000] Set defult RDRegion value:  CountryCode=EU 11
[   19.420000] <==== rt28xx_init, Status=0
[   19.420000] ipaccount: ifname [apclii0] event[16]
[   19.430000] ipaccount: ifname [apclii0] event[5]
[   19.430000] ipaccount: ifname [wl0] event[1]
[   21.340000] ipaccount: ifname [wl0] event[20]
[   21.350000] device wl0 entered promiscuous mode
[   21.350000] br-lan: port 2(wl0) entered forwarding state
[   21.360000] br-lan: port 2(wl0) entered forwarding state
[   23.360000] br-lan: port 2(wl0) entered forwarding state
[   23.930000] ipaccount: ifname [wl1] event[13]
[   23.930000] TX_BCN DESC a366a000 size = 320
[   23.940000] RX[0] DESC a366c000 size = 2048
[   23.940000] RX[1] DESC a366d000 size = 1024
[   23.950000] E2pAccessMode=2
[   23.960000] cfg_mode=9
[   23.960000] cfg_mode=9
[   23.960000] wmode_band_equal(): Band Equal!
[   24.040000] load fw image from fw_header_image
[   24.040000] AndesMTLoadFwMethod1(2181)::pChipCap->fw_len(63984)
[   24.050000] CmdAddressLenReq:(ret = 0)
[   24.050000] AndesInitCmdMsg:cmd_type:238,ExtCmdType:0
[   24.060000] AndesInitCmdMsg:cmd_type:238,ExtCmdType:0
[   24.070000] AndesInitCmdMsg:cmd_type:238,ExtCmdType:0
[   24.070000] AndesInitCmdMsg:cmd_type:238,ExtCmdType:0
[   24.080000] AndesInitCmdMsg:cmd_type:238,ExtCmdType:0
[   24.080000] AndesInitCmdMsg:cmd_type:238,ExtCmdType:0
[   24.090000] AndesInitCmdMsg:cmd_type:238,ExtCmdType:0
[   24.090000] AndesInitCmdMsg:cmd_type:238,ExtCmdType:0
[   24.100000] AndesInitCmdMsg:cmd_type:238,ExtCmdType:0
[   24.100000] AndesInitCmdMsg:cmd_type:238,ExtCmdType:0
[   24.110000] AndesInitCmdMsg:cmd_type:238,ExtCmdType:0
[   24.110000] AndesInitCmdMsg:cmd_type:238,ExtCmdType:0
[   24.120000] AndesInitCmdMsg:cmd_type:238,ExtCmdType:0
[   24.120000] AndesInitCmdMsg:cmd_type:238,ExtCmdType:0
[   24.130000] AndesInitCmdMsg:cmd_type:238,ExtCmdType:0
[   24.130000] AndesInitCmdMsg:cmd_type:238,ExtCmdType:0
[   24.140000] CmdFwStartReq: override = 1, address = 1048576
[   24.140000] CmdStartDLRsp: WiFI FW Download Success
[   24.180000] MtAsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC)
[   24.180000] efuse_probe: efuse = 10000002
[   24.190000] RtmpChipOpsEepromHook::e2p_type=2, inf_Type=4
[   24.190000] RtmpEepromGetDefault::e2p_dafault=2
[   24.200000] RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 2
[   24.200000] NVM is FLASH mode
[   24.210000] 1. Phy Mode = 14
[   24.410000] Country Region from e2p = ffff
[   24.420000] tssi_1_target_pwr_g_band = 22
[   24.420000] 2. Phy Mode = 14
[   24.430000] 3. Phy Mode = 14
[   24.430000] NICInitPwrPinCfg(11): Not support for HIF_MT yet!
[   24.430000] NICInitializeAsic(652): Not support rtmp_mac_sys_reset () for HIF_MT yet!
[   24.440000] mt_mac_init()-->
[   24.450000] MtAsicInitMac()-->
[   24.710000] mt7628_init_mac_cr()-->
[   24.710000] MtAsicSetMacMaxLen(1279): Set the Max RxPktLen=1024!
[   24.720000] <--mt_mac_init()
[   24.720000] 	WTBL Segment 1 info:
[   24.730000] 		MemBaseAddr/FID:0x28000/0
[   24.730000] 		EntrySize/Cnt:32/128
[   24.730000] 	WTBL Segment 2 info:
[   24.740000] 		MemBaseAddr/FID:0x40000/0
[   24.740000] 		EntrySize/Cnt:64/128
[   24.740000] 	WTBL Segment 3 info:
[   24.750000] 		MemBaseAddr/FID:0x42000/64
[   24.750000] 		EntrySize/Cnt:64/128
[   24.750000] 	WTBL Segment 4 info:
[   24.760000] 		MemBaseAddr/FID:0x44000/128
[   24.760000] 		EntrySize/Cnt:32/128
[   24.770000] AntCfgInit(2925): Not support for HIF_MT yet!
[   24.770000] MCS Set = ff ff 00 00 00
[   24.770000] MtAsicSetChBusyStat(846): Not support for HIF_MT yet!
[   27.560000] MtAsicSetRalinkBurstMode(2971): Not support for HIF_MT yet!
[   27.560000] MtAsicSetPiggyBack(783): Not support for HIF_MT yet!
[   27.590000] MtAsicSetTxPreamble(2950): Not support for HIF_MT yet!
[   27.600000] MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0
[   27.600000] Main bssid = 88:c3:97:XX:XX:XX
[   27.610000] <==== rt28xx_init, Status=0
[   27.610000] ipaccount: ifname [wl2] event[16]
[   27.620000] ipaccount: ifname [wl2] event[5]
[   27.620000] ipaccount: ifname [wl3] event[16]
[   27.630000] ipaccount: ifname [wl3] event[5]
[   27.630000] ipaccount: ifname [apcli0] event[16]
[   27.640000] ipaccount: ifname [apcli0] event[5]
[   27.640000] ipaccount: ifname [apcli1] event[16]
[   27.650000] ipaccount: ifname [apcli1] event[5]
[   27.650000] !!!mt7628_xq_board=R4AC!!!
[   27.650000] ipaccount: ifname [wl1] event[1]
[   27.660000] CmdSlotTimeSet start
[   27.700000] CmdSlotTimeSet end
[   30.190000] ipaccount: ifname [wl1] event[20]
[   30.190000] device wl1 entered promiscuous mode
[   30.200000] br-lan: port 3(wl1) entered forwarding state
[   30.210000] br-lan: port 3(wl1) entered forwarding state
[   30.230000] ipaccount: ifname [wl2] event[13]
[   30.240000] ##### mbss_cr_enable, BssId = 1
[   30.240000] ipaccount: ifname [wl2] event[1]
[   32.210000] br-lan: port 3(wl1) entered forwarding state
[   32.290000] enable ip account module.
rcS S calling: /etc/rc.d/S20network boot: WARNING: EXITCODE=0, execute too slow, 20 >= 15: /etc/rc.d/S20network boot
[   32.630000] dev_redirect: add(+) dev redirect mapping: src:eth0.2->dst:ifb0
Fri Feb 28 08:33:09 CET 2020 boot_check[3035]: INFO: Wireless OK
[   45.090000] dev_redirect: add(+) dev redirect mapping: src:eth0.2->dst:ifb0
[   46.390000] ipaccount: refresh dev ifname to [eth0 wl0 wl1 wl3] 
[   46.400000] ipaccount: landev_init_all() add dev [eth0] is_wireless: 0.
[   46.410000] ipaccount: landev_init_all() add dev [wl0] is_wireless: 1.
[   46.410000] ipaccount: landev_init_all() add dev [wl1] is_wireless: 1.
[   46.420000] ipaccount: landev_init_all() add dev [wl3] is_wireless: 1.
[   46.480000] dev_redirect OFF.
[   46.570000] dev_redirect OFF.dev_redirect OFF.
[   48.330000] dev_redirect OFF.dev_redirect OFF.ipaccount: landev_init_all() add dev [eth0] is_wireless: 0.
[   49.630000] ipaccount: landev_init_all() add dev [wl0] is_wireless: 1.
[   49.640000] ipaccount: landev_init_all() add dev [wl1] is_wireless: 1.
[   49.640000] ipaccount: landev_init_all() add dev [wl3] is_wireless: 1.
[   51.410000] xqfp: forward hooks init success!
[   51.420000] xqfp:pre hooks init success!
[   51.420000] xqfp:extend init success!
[   51.430000] xqfp: register_netdevice_notifier_v3!
[   51.430000] xqfp: module init success!
rcS S boot: INFO: rcS S boot timing 44 seconds.
Fri Feb 28 08:33:18 CET 2020 INFO: rcS S boot timing 44 seconds.
rcS S boot: system type(R4AC/2): SQUASH/3
Fri Feb 28 08:33:19 CET 2020 system type(R4AC/2): SQUASH/3
rcS S boot: ROOTFS: /dev/root on / type squashfs (ro,relatime)
Fri Feb 28 08:33:19 CET 2020 ROOTFS: /dev/root on / type squashfs (ro,relatime)
[   54.600000] led=44, on=1, off=4000, blinks,=1, reset=1, time=4000
[   54.600000] led=11, on=1, off=4000, blinks,=1, reset=1, time=4000
[   54.630000] led=44, on=1, off=4000, blinks,=1, reset=1, time=4000
[   54.870000] led=11, on=4000, off=1, blinks,=1, reset=1, time=4000
uci: Entry not found
Fri Feb 28 08:33:21 CET 2020 boot_check[4138]: Booting up finished.
[   61.720000] Started WatchDog Timer.

See also